 |
|
|
|
Next: P2BS Memory Question
|
| Author |
Message |
External
Since: Nov 24, 2004
Posts: 5
|
(Msg. 1) Posted: Wed Nov 24, 2004 6:09 pm
Post subject: AN35N-Ultra Will Not Detect Drives
Archived from groups: alt>comp>periphs>mainboard>shuttle (more info?)
|
|
|
Having problems with motherboards. Six month old system I built with
AN35N-Ultra motherboard stopped working. Stripped it down to the
power supply processor and motherboard and did not get any post beeps
so figured board was bad. Purchased new AN35N-Ultra and now I have a
new problem. I connected everything back the same way of the original
configuration same exact parts just new motherboard. System will
start post but will hang up on hard drive auto detect. I have one WD
80gig drive on primary IDE channel and one DVD-RW on secondary
channel, both worked fine with this configuration before. Checked
bios and both channels are enabled and set on auto detect. So I
removed the DVD-RW IDE cable and the system booted up fine. Next I
switched the WD hard drive to the secondary IDE channel that the DVD
was on, again system booted up fine. Tried to connect a second hard
drive to the other channel and again it locked up on the hard drive
auto detect. I also tried to put the second hard drive in a slave
position on the same IDE channel with the main WD hard drive as master
and again it locked up. If I connect anything more than one hard
drive to the motherboard it will stop on hard drive auto detect.
Anyone have a clue as to the problem? Another bad motherboard?
Checked all the power cables, seem to be fine. Made sure all the
jumpers on the drives were in the proper place, slave master or single
drive. What to do now? |
|
| Back to top |
|
 | |
External
Since: Aug 17, 2004
Posts: 10
|
(Msg. 2) Posted: Wed Nov 24, 2004 10:35 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Al wrote:
> Having problems with motherboards. Six month old system I built with
> AN35N-Ultra motherboard stopped working. Stripped it down to the
> power supply processor and motherboard and did not get any post beeps
> so figured board was bad. Purchased new AN35N-Ultra and now I have a
> new problem. I connected everything back the same way of the original
> configuration same exact parts just new motherboard. System will
> start post but will hang up on hard drive auto detect. I have one WD
> 80gig drive on primary IDE channel and one DVD-RW on secondary
> channel, both worked fine with this configuration before. Checked
> bios and both channels are enabled and set on auto detect. So I
> removed the DVD-RW IDE cable and the system booted up fine. Next I
> switched the WD hard drive to the secondary IDE channel that the DVD
> was on, again system booted up fine. Tried to connect a second hard
> drive to the other channel and again it locked up on the hard drive
> auto detect. I also tried to put the second hard drive in a slave
> position on the same IDE channel with the main WD hard drive as master
> and again it locked up. If I connect anything more than one hard
> drive to the motherboard it will stop on hard drive auto detect.
> Anyone have a clue as to the problem? Another bad motherboard?
> Checked all the power cables, seem to be fine. Made sure all the
> jumpers on the drives were in the proper place, slave master or single
> drive. What to do now?
New IDE cables? And set the jumpers on all drives to "cable select".
--
FRH<!-- ~MESSAGE_AFTER~ --> |
|
| Back to top |
|
| |
External
Since: Dec 28, 2003
Posts: 332
|
(Msg. 3) Posted: Thu Nov 25, 2004 4:35 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
The more hard drives, the power is need, maybe your power supply is going
bad.
A bad power supply could have caused your original AN35N motherboard to go
bad
Try clearing the bios, unplug the power cable, then Clear CMOS (jp-1 jumper)
for 30 seconds,
then plug power cable back in, then reset your bios setting.
"Al" <al849.DeleteThis@hotmail.com> wrote in message
news:e19d6989.0411241809.5108f16f@posting.google.com...
> Having problems with motherboards. Six month old system I built with
> AN35N-Ultra motherboard stopped working. Stripped it down to the
> power supply processor and motherboard and did not get any post beeps
> so figured board was bad. Purchased new AN35N-Ultra and now I have a
> new problem. I connected everything back the same way of the original
> configuration same exact parts just new motherboard. System will
> start post but will hang up on hard drive auto detect. I have one WD
> 80gig drive on primary IDE channel and one DVD-RW on secondary
> channel, both worked fine with this configuration before. Checked
> bios and both channels are enabled and set on auto detect. So I
> removed the DVD-RW IDE cable and the system booted up fine. Next I
> switched the WD hard drive to the secondary IDE channel that the DVD
> was on, again system booted up fine. Tried to connect a second hard
> drive to the other channel and again it locked up on the hard drive
> auto detect. I also tried to put the second hard drive in a slave
> position on the same IDE channel with the main WD hard drive as master
> and again it locked up. If I connect anything more than one hard
> drive to the motherboard it will stop on hard drive auto detect.
> Anyone have a clue as to the problem? Another bad motherboard?
> Checked all the power cables, seem to be fine. Made sure all the
> jumpers on the drives were in the proper place, slave master or single
> drive. What to do now?
><!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Nov 24, 2004
Posts: 5
|
(Msg. 4) Posted: Fri Nov 26, 2004 4:34 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"Tod" <no_spam_me.RemoveThis@comcast.net> wrote in message news:<Sarpd.98122$5K2.59160@attbi_s03>...
> The more hard drives, the power is need, maybe your power supply is going
> bad.
> A bad power supply could have caused your original AN35N motherboard to go
> bad
>
> Try clearing the bios, unplug the power cable, then Clear CMOS (jp-1 jumper)
> for 30 seconds,
> then plug power cable back in, then reset your bios setting.
>
I don't have any way to check power supply other than replaceing it.
Tried clearing the CMOS, but did not have any effect on problem.<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Aug 12, 2004
Posts: 54
|
(Msg. 5) Posted: Fri Nov 26, 2004 8:28 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
You might want to invest in a power supply tester. I use mine all the
time, and it's found problems for me. Newegg has a Powmax for $14,
including shipping, and its accurate. BTW-if your first board was
only 6 months old isn't it still under warranty? >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Dec 28, 2003
Posts: 332
|
(Msg. 6) Posted: Sat Nov 27, 2004 1:35 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Order a cheap power supply off <a style='text-decoration: underline;' href="http://www.pricewatch.com" target="_blank">www.pricewatch.com</a>
or <a style='text-decoration: underline;' href="http://www.ebay.com" target="_blank">www.ebay.com</a>
"Al" <al849 DeleteThis @hotmail.com> wrote in message
news:e19d6989.0411260434.517d5e90@posting.google.com...
> "Tod" <no_spam_me DeleteThis @comcast.net> wrote in message
> news:<Sarpd.98122$5K2.59160@attbi_s03>...
>> The more hard drives, the power is need, maybe your power supply is going
>> bad.
>> A bad power supply could have caused your original AN35N motherboard to
>> go
>> bad
>>
>> Try clearing the bios, unplug the power cable, then Clear CMOS (jp-1
>> jumper)
>> for 30 seconds,
>> then plug power cable back in, then reset your bios setting.
>>
> I don't have any way to check power supply other than replaceing it.
> Tried clearing the CMOS, but did not have any effect on problem.
><!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Nov 27, 2004
Posts: 1
|
(Msg. 7) Posted: Sat Nov 27, 2004 3:26 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"Tod" <no_spam_me DeleteThis @comcast.net> wrote in message news:<86Upd.673715$8_6.43977@attbi_s04>...
<font color=purple> > Order a cheap power supply off <a style='text-decoration: underline;' href="http://www.pricewatch.com</font" target="_blank">www.pricewatch.com</font</a>>
<font color=purple> > or <a style='text-decoration: underline;' href="http://www.ebay.com</font" target="_blank">www.ebay.com</font</a>>
>
Another odd thing, when I checked the device manager it has my
Western Digital 80 gig IDE hard drive listed as a SCSI Disk device.
WDC W080 0JB-00FMA0 SCSI Disk Device<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Dec 28, 2003
Posts: 332
|
(Msg. 8) Posted: Sun Nov 28, 2004 2:35 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Any added on controller (IDE/ATA or SCSI) will be listed in Device Manger as
SCSI.
Have you added an extra controller ?
"jerry" <rst121.TakeThisOut@juno.com> wrote in message
news:e0e926c2.0411271526.3ee30e13@posting.google.com...
> "Tod" <no_spam_me.TakeThisOut@comcast.net> wrote in message
> news:<86Upd.673715$8_6.43977@attbi_s04>...
<font color=green> >> Order a cheap power supply off <a style='text-decoration: underline;' href="http://www.pricewatch.com</font" target="_blank">www.pricewatch.com</font</a>>
<font color=green> >> or <a style='text-decoration: underline;' href="http://www.ebay.com</font" target="_blank">www.ebay.com</font</a>>
>>
>
>
> Another odd thing, when I checked the device manager it has my
> Western Digital 80 gig IDE hard drive listed as a SCSI Disk device.
> WDC W080 0JB-00FMA0 SCSI Disk Device
><!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Nov 24, 2004
Posts: 5
|
(Msg. 9) Posted: Sun Nov 28, 2004 6:24 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"Tod" <no_spam_me RemoveThis @comcast.net> wrote in message news:<cyeqd.108657$5K2.78651@attbi_s03>...
> Any added on controller (IDE/ATA or SCSI) will be listed in Device Manger as
> SCSI.
> Have you added an extra controller ?
>
No, I have not added any extra controller cards all though
I thought that might be a way to fix the problem.<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Nov 24, 2004
Posts: 5
|
(Msg. 10) Posted: Sat Dec 04, 2004 1:57 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Installed new 500w power supply. No help.
Looks like just another bad main board.
Everyone seems to love these Shuttle AN35N boards, but
I have had nothing but bad experience. Third replacement is on
the way from newegg. Hope third time is the charm! >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Sep 26, 2004
Posts: 43
|
(Msg. 11) Posted: Sun Dec 05, 2004 2:28 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
and you are using the cables that came with the board?
"Al" <al849.TakeThisOut@hotmail.com> wrote in message
news:e19d6989.0412041357.27503f49@posting.google.com...
> Installed new 500w power supply. No help.
> Looks like just another bad main board.
> Everyone seems to love these Shuttle AN35N boards, but
> I have had nothing but bad experience. Third replacement is on
> the way from newegg. Hope third time is the charm!<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Nov 24, 2004
Posts: 5
|
(Msg. 12) Posted: Sun Dec 05, 2004 9:23 am
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"dave AKA vwdoc1" <vwdoc1 RemoveThis @ameritech.net> wrote in message news:<Dnusd.28738$Rf1.573@newssvr19.news.prodigy.com>...
> and you are using the cables that came with the board?
>
Tried the cables that came with the board, also bought some new
round cables. No luck with any of them.<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
External
Since: Sep 26, 2004
Posts: 43
|
(Msg. 13) Posted: Sun Dec 05, 2004 7:11 pm
Post subject: Re: AN35N-Ultra Will Not Detect Drives [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
well good luck with the new board! 
"Al" <al849.DeleteThis@hotmail.com> wrote in message
news:e19d6989.0412050923.4736a51d@posting.google.com...
> "dave AKA vwdoc1" <vwdoc1.DeleteThis@ameritech.net> wrote in message
> news:<Dnusd.28738$Rf1.573@newssvr19.news.prodigy.com>...
>> and you are using the cables that came with the board?
>>
>
>
> Tried the cables that came with the board, also bought some new
> round cables. No luck with any of them.<!-- ~MESSAGE_AFTER~ --> >> Stay informed about: AN35N-Ultra Will Not Detect Drives |
|
| Back to top |
|
| |
| Related Topics: | AN35N Ultra - I recently bought 2 AN35N Ultra boards. When they post and I attempt to enter the bios setup by pressing the delete key, nothing happens for 20-30 seconds and then it enters the bios setup. Also, it has the same delay when it attempts to identify the ide...
AN35N Ultra - Hi @ all, first please excuse my bad english, i'm from Germany. ;-) I'm using a Shuttle AN35N Ultra and an Barton XP 2500+. I've tried to Overclock by setting the FSB to 200MHz and 1.750 Vcore. Runs nearly a Minute as 3200+ and then shuts down with the...
Got The AN35n ultra - What's next? - My trustly ol AK35GT went into cardiac arrest after I upgraded the BIOS (or at least tried to--!!) . So, I just puchased the AN35N Ultra to replace it. The system will have little game use, but will be used mostly for burning DVDs and some transferring...
AN35N Ultra does not support DOS DMA - AN35N Ultra does not support DOS DMA, which is necessary to run Ghost or PQDI at a decent disk speed. fwiw! hth -- Kristi Shuttle AN35N Ultra, XP1700 Tbred A 168x11 1.848gHz, WinXP pro SP1(SP2), GeF3 Ti200, DX9.0b, 512mb @336
AN35N Ultra and SCSI - Any ideas why all of my drives show up as SCSI in XP pro and AN35N Ultra? I have a cd and dvd burner and a 200 GB hdd hooked up to the 2 IDE connections on my motherboard. Device manage in XP shows them as scsi and nothing under IDE ATA/ Atapi.. |
|
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
FAQ
Profile
Private Messages
Log in
