|
Related Topics:
| Help with SD11 - I've just recently gotten a new FIC SD11 with no support drivers from ebay. Long story, a mistake on my part, but I'm trying to make the best of it. What I need are the drivers on CD-Pro 4.0. FIC has made drivers from every edition of CD-Pro back to 4.1.
Need Help with SD11 - I inherited an old SD11 and have to re-instal Windows 98. It has a network card since someone used it for boadband. This net card conflicts with the modem that is also The netcard shows the dialup adapter under device manager. Theere is one..
SD11 pin connections - I just bought a SD11, my button board pic does not match what the manual shows. Where there should be two rows of pins, I have only one row of pins. I am confused. any help would be nice.
Troubles upgrading an SD11 - I'm to get a little more life out of an old SlotA Athlon box. The MB is an FIC SD11, with 128 megs of pc100 and the current processor is a K7 600 with AMI bios, vNC610. The specs from FIC state that the board will support up to an..
HD light stays on for SD11 - I have changed the drive cable but cannot get the drive lght to go off so that it will boot. The drive is fine on another computer when I place it there. Please advise me as to the problem. Thanks.
|
|
|
Next: FIC: 503+, & 2013 BIOS PW's
|
| Author |
Message |
External
Since: Jul 16, 2003
Posts: 4
|
(Msg. 1) Posted: Thu Jul 17, 2003 1:19 am
Post subject: SD11
Archived from groups: alt>comp>periphs>mainboard>fic (more info?)
|
|
|
Help anyone,
I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of the
SD11 that I thought was bad. It would not reboot. (tries to but would seem
to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got one,
put it in and, viola, it does the same thing! So I cleared the bios setting
with the jumper, rebooted, and it still goes into sleep mode. (I'm not sure
it really is in sleep mode, but the monitor goes into low power, and the
booting process stops. If I clear the bios & hit the switch, it says cmos
setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
default values. I've changed just about everything in SETUP to no avail. If
I hit F2 and take defaults, it will boot and run okay until I have to reboot
again. Then I must go through the same process again. Anyone have any ideas
about this? Thanks! |
|
| Back to top |
|
 | |
External
Since: Dec 18, 2003
Posts: 81
|
(Msg. 2) Posted: Thu Jul 17, 2003 3:43 am
Post subject: Re: SD11 [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"Dennis" <denaas RemoveThis @swbell.net> wrote in message news:CbkRa.56$La.27509872@newssvr11.news.prodigy.com...
> Help anyone,
>
> I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of the
> SD11 that I thought was bad. It would not reboot. (tries to but would seem
> to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got one,
> put it in and, viola, it does the same thing! So I cleared the bios setting
> with the jumper, rebooted, and it still goes into sleep mode. (I'm not sure
> it really is in sleep mode, but the monitor goes into low power, and the
> booting process stops. If I clear the bios & hit the switch, it says cmos
> setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
> default values. I've changed just about everything in SETUP to no avail. If
> I hit F2 and take defaults, it will boot and run okay until I have to reboot
> again. Then I must go through the same process again. Anyone have any ideas
> about this? Thanks!
>
Have you tried swapping the memory, even a single known good stick might do.
Den
--
artificial hippocampus
I wish I could remember
what is means.<!-- ~MESSAGE_AFTER~ --> |
|
| Back to top |
|
| |
External
Since: Jul 16, 2003
Posts: 4
|
(Msg. 3) Posted: Thu Jul 17, 2003 3:43 am
Post subject: Re: SD11 [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Yes I have tried memory swaps. No luck though. Thanks for the reply.
"Den" <Den DeleteThis @NoSpamOrNoCornedBeef.unlimited-But-Was-Limited.RIP> wrote in
message news:bf4nks$jh4$1@newsg1.svr.pol.co.uk...
>
> "Dennis" <denaas DeleteThis @swbell.net> wrote in message
news:CbkRa.56$La.27509872@newssvr11.news.prodigy.com...
> > Help anyone,
> >
> > I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of
the
> > SD11 that I thought was bad. It would not reboot. (tries to but would
seem
> > to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got
one,
> > put it in and, viola, it does the same thing! So I cleared the bios
setting
> > with the jumper, rebooted, and it still goes into sleep mode. (I'm not
sure
> > it really is in sleep mode, but the monitor goes into low power, and the
> > booting process stops. If I clear the bios & hit the switch, it says
cmos
> > setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
> > default values. I've changed just about everything in SETUP to no
avail. If
> > I hit F2 and take defaults, it will boot and run okay until I have to
reboot
> > again. Then I must go through the same process again. Anyone have any
ideas
> > about this? Thanks!
> >
> Have you tried swapping the memory, even a single known good stick might
do.
>
> Den
> --
> artificial hippocampus
> I wish I could remember
> what is means.
>
>
><!-- ~MESSAGE_AFTER~ --> >> Stay informed about: SD11 |
|
| Back to top |
|
| |
|
FAQ
Search
Profile
Private Messages
Log in/Register/Password
