How can I use 2 power supplies at once

'Dirty Harry' wrote:
| I don't have money of a new PS but I have plenty of old ones lying around.
| I'd like to use the 350 for the computer and a 250 for the hard drives
| (5)...I know the green wire has something to do with starting up the
| ps...help me out guys .
_____

If you use one power supply for the motherboard and slots, another for the
drives, you should be ok. It is a bad idea to connect two power supplies in
parallel to the motherboard.

#1. You might have a alternative for the drives. Drives don't use much
power except when spinning up. Some BIOS have a setting to delay hard drive
spin-up (spin-up is staggered over a short period of time.

#2. Check at the manufacturer web site for each of your hard drives and add
up the power consumption. You will find that most drives use less power
than you think.

#3. Keep in mind that at the time your graphics card might be demanding the
most power that it is unlikely that you will have many of the drives using
more than average power.

#4. An ATX12V power supply has 'load sharing'. That means power is shifted
to what ever voltage rails require it. The TOTAL power output is limited to
the over all supply rating, but individual voltages can use up to perhaps
80% of the total supply rating.


I recommend you check the amount of power your really need before
jury-rigging two power supplies. And check to see if the larger single
power supply alone causes any problems.

See
http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf
for ATX12V specifications and information on
load sharing
connector pin-out
Power ON#
Power Good.

Phil Weldon



"Dirty Harry" <nothin.DeleteThis@nowhere.com> wrote in message
news:_PAri.19239$fJ5.9990@pd7urf1no...
|I don't have money of a new PS but I have plenty of old ones lying around.
| I'd like to use the 350 for the computer and a 250 for the hard drives
| (5)...I know the green wire has something to do with starting up the
| ps...help me out guys .
|
|
 >> Stay informed about: How can I use 2 power supplies at once 

"Phil Weldon" <not.disclosed.RemoveThis@example.com> wrote in message
news:15Lri.12778$rR.12575@newsread2.news.pas.earthlink.net...
> 'Dirty Harry' wrote:
> | I don't have money of a new PS but I have plenty of old ones lying
> around.
> | I'd like to use the 350 for the computer and a 250 for the hard drives
> | (5)...I know the green wire has something to do with starting up the
> | ps...help me out guys .
> _____
>
> If you use one power supply for the motherboard and slots, another for the
> drives, you should be ok. It is a bad idea to connect two power supplies
> in
> parallel to the motherboard.
>
> #1. You might have a alternative for the drives. Drives don't use much
> power except when spinning up. Some BIOS have a setting to delay hard
> drive
> spin-up (spin-up is staggered over a short period of time.
>
> #2. Check at the manufacturer web site for each of your hard drives and
> add
> up the power consumption. You will find that most drives use less power
> than you think.
>
> #3. Keep in mind that at the time your graphics card might be demanding
> the
> most power that it is unlikely that you will have many of the drives using
> more than average power.
>
> #4. An ATX12V power supply has 'load sharing'. That means power is
> shifted
> to what ever voltage rails require it. The TOTAL power output is limited
> to
> the over all supply rating, but individual voltages can use up to perhaps
> 80% of the total supply rating.
>
>
> I recommend you check the amount of power your really need before
> jury-rigging two power supplies. And check to see if the larger single
> power supply alone causes any problems.
>
> See
> http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf
> for ATX12V specifications and information on
> load sharing
> connector pin-out
> Power ON#
> Power Good.
>
> Phil Weldon


My problem is that the 12v line is dropping all the way down to 11.5 when
the system is under load. I have 2 raid arrays and one usb HD so there is a
total of 5 drives all together. I think i'm going to do this, set a power
supply for the hard drives on a switch (green connected to a ground) and
then fire that up first and then turn on the computer power. The system is
always running 24/7 so it shouldn't be too much of an issue for booting up.
What do ya think?
 >> Stay informed about: How can I use 2 power supplies at once 

'DeanB' wrote:
| My problem is that the 12v line is dropping all the way down to 11.5 when
| the system is under load. I have 2 raid arrays and one usb HD so there is
a
| total of 5 drives all together. I think i'm going to do this, set a power
| supply for the hard drives on a switch (green connected to a ground) and
| then fire that up first and then turn on the computer power. The system
is
| always running 24/7 so it shouldn't be too much of an issue for booting
up.
| What do ya think?
_____

The specifications of ATX12V for the 12 volt lines are 12 volts +/- 5%, or
11.4 to 12.6 volts, so your readings are within specifications ( see
<http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf>
3.2.1 DC Voltage Regulation
page 12)

If you are not actually having problems, I wouldn't change things. (The USB
hard drive has its own power supply, a wall wart, right?)

If you do use the second power supply, I think your method is the way to go.

Phil Weldon

"Dirty Harry" <nothin.RemoveThis@nowhere.com> wrote in message
news:QKLri.18691$_d2.5693@pd7urf3no...
|
| "Phil Weldon" <not.disclosed.RemoveThis@example.com> wrote in message
| news:15Lri.12778$rR.12575@newsread2.news.pas.earthlink.net...
| > 'Dirty Harry' wrote:
| > | I don't have money of a new PS but I have plenty of old ones lying
| > around.
| > | I'd like to use the 350 for the computer and a 250 for the hard drives
| > | (5)...I know the green wire has something to do with starting up the
| > | ps...help me out guys .
| > _____
| >
| > If you use one power supply for the motherboard and slots, another for
the
| > drives, you should be ok. It is a bad idea to connect two power
supplies
| > in
| > parallel to the motherboard.
| >
| > #1. You might have a alternative for the drives. Drives don't use much
| > power except when spinning up. Some BIOS have a setting to delay hard
| > drive
| > spin-up (spin-up is staggered over a short period of time.
| >
| > #2. Check at the manufacturer web site for each of your hard drives and
| > add
| > up the power consumption. You will find that most drives use less power
| > than you think.
| >
| > #3. Keep in mind that at the time your graphics card might be demanding
| > the
| > most power that it is unlikely that you will have many of the drives
using
| > more than average power.
| >
| > #4. An ATX12V power supply has 'load sharing'. That means power is
| > shifted
| > to what ever voltage rails require it. The TOTAL power output is
limited
| > to
| > the over all supply rating, but individual voltages can use up to
perhaps
| > 80% of the total supply rating.
| >
| >
| > I recommend you check the amount of power your really need before
| > jury-rigging two power supplies. And check to see if the larger single
| > power supply alone causes any problems.
| >
| > See
| > http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf
| > for ATX12V specifications and information on
| > load sharing
| > connector pin-out
| > Power ON#
| > Power Good.
| >
| > Phil Weldon
|
|
| My problem is that the 12v line is dropping all the way down to 11.5 when
| the system is under load. I have 2 raid arrays and one usb HD so there is
a
| total of 5 drives all together. I think i'm going to do this, set a power
| supply for the hard drives on a switch (green connected to a ground) and
| then fire that up first and then turn on the computer power. The system
is
| always running 24/7 so it shouldn't be too much of an issue for booting
up.
| What do ya think?
|
|
 >> Stay informed about: How can I use 2 power supplies at once 

'DeanB' wrote:
| My problem is that the 12v line is dropping all the way down to 11.5 when
| the system is under load. I have 2 raid arrays and one usb HD so there
| is a total of 5 drives all together. I think i'm going to do this, set a
power
| supply for the hard drives on a switch (green connected to a ground) and
| then fire that up first and then turn on the computer power. The system
| is always running 24/7 so it shouldn't be too much of an issue for booting
| up. What do ya think?
_____

The specifications of ATX12V for the 12 volt lines are 12 volts +/- 5%, or
11.4 to 12.6 volts, so your readings are within specifications ( see
<http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf>
3.2.1 DC Voltage Regulation
page 12)

If you are not actually having problems, I wouldn't change things. (The USB
hard drive has its own power supply, a wall wart, right?)

If you do use the second power supply, I think your method is the way to go.

Phil Weldon

"Dirty Harry" <nothin DeleteThis @nowhere.com> wrote in message
news:QKLri.18691$_d2.5693@pd7urf3no...
|
| "Phil Weldon" <not.disclosed DeleteThis @example.com> wrote in message
| news:15Lri.12778$rR.12575@newsread2.news.pas.earthlink.net...
| > 'Dirty Harry' wrote:
| > | I don't have money of a new PS but I have plenty of old ones lying
| > around.
| > | I'd like to use the 350 for the computer and a 250 for the hard drives
| > | (5)...I know the green wire has something to do with starting up the
| > | ps...help me out guys .
| > _____
| >
| > If you use one power supply for the motherboard and slots, another for
the
| > drives, you should be ok. It is a bad idea to connect two power
supplies
| > in
| > parallel to the motherboard.
| >
| > #1. You might have a alternative for the drives. Drives don't use much
| > power except when spinning up. Some BIOS have a setting to delay hard
| > drive
| > spin-up (spin-up is staggered over a short period of time.
| >
| > #2. Check at the manufacturer web site for each of your hard drives and
| > add
| > up the power consumption. You will find that most drives use less power
| > than you think.
| >
| > #3. Keep in mind that at the time your graphics card might be demanding
| > the
| > most power that it is unlikely that you will have many of the drives
using
| > more than average power.
| >
| > #4. An ATX12V power supply has 'load sharing'. That means power is
| > shifted
| > to what ever voltage rails require it. The TOTAL power output is
limited
| > to
| > the over all supply rating, but individual voltages can use up to
perhaps
| > 80% of the total supply rating.
| >
| >
| > I recommend you check the amount of power your really need before
| > jury-rigging two power supplies. And check to see if the larger single
| > power supply alone causes any problems.
| >
| > See
| > http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf
| > for ATX12V specifications and information on
| > load sharing
| > connector pin-out
| > Power ON#
| > Power Good.
| >
| > Phil Weldon
|
|
| My problem is that the 12v line is dropping all the way down to 11.5 when
| the system is under load. I have 2 raid arrays and one usb HD so there is
a
| total of 5 drives all together. I think i'm going to do this, set a power
| supply for the hard drives on a switch (green connected to a ground) and
| then fire that up first and then turn on the computer power. The system
is
| always running 24/7 so it shouldn't be too much of an issue for booting
up.
| What do ya think?
|
|
 >> Stay informed about: How can I use 2 power supplies at once 

"Phil Weldon" <not.disclosed DeleteThis @example.com> wrote in message
news:w3Mri.14336$zA4.11748@newsread3.news.pas.earthlink.net...
> 'DeanB' wrote:
> | My problem is that the 12v line is dropping all the way down to 11.5
> when
> | the system is under load. I have 2 raid arrays and one usb HD so there
> | is a total of 5 drives all together. I think i'm going to do this, set
> a
> power
> | supply for the hard drives on a switch (green connected to a ground) and
> | then fire that up first and then turn on the computer power. The
> system
> | is always running 24/7 so it shouldn't be too much of an issue for
> booting
> | up. What do ya think?
> _____
>
> The specifications of ATX12V for the 12 volt lines are 12 volts +/- 5%, or
> 11.4 to 12.6 volts, so your readings are within specifications ( see
> <http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf>
> 3.2.1 DC Voltage Regulation
> page 12)
>
> If you are not actually having problems, I wouldn't change things. (The
> USB
> hard drive has its own power supply, a wall wart, right?)
>
> If you do use the second power supply, I think your method is the way to
> go.
>
> Phil Weldon
>


I'm not having any problems at stock speeds, I can't OC this thing at all
though lol. Just feel like having some fun squeezing some extra speed out
of it. Its an amd 3800+ 64 bit....My GF's 3700+ can overclock like crazy
(230+fsb) I turn this one up to 203 fsb and I'm crashing lol. The problem
is I'm only using a generic 400w ps I think...I just wanna see if that's my
OC problem or not...I know I know, get a real power supply hehe...I will
when I have some moola.
Thanks for the advice!
Cheers
 >> Stay informed about: How can I use 2 power supplies at once 

'Dirty Harry' wrote:
| I'm not having any problems at stock speeds, I can't OC this thing at all
| though lol. Just feel like having some fun squeezing some extra speed out
| of it. Its an amd 3800+ 64 bit....My GF's 3700+ can overclock like crazy
| (230+fsb) I turn this one up to 203 fsb and I'm crashing lol. The
problem
| is I'm only using a generic 400w ps I think...I just wanna see if that's
my
| OC problem or not...I know I know, get a real power supply hehe...I will
| when I have some moola.
| Thanks for the advice!
_____

It's worth trying. I'd suggest that you might putting as many drives as
possible in standby, and then checking the 12 volts supply reading. And
then doing the same when trying to overclock. It might turn out to be a
voltage quality rather than quantity issue, or the phase of the moon B^) I
will admit that in days gone by I've used some $12 US power supplies to
overclock Celeron 'Coppermine' and Pentium III CPUs with no issues. These
days nearly all power drawn from the + 12 volt line is down converted and
regulated again before use (save for the drive motors, and those are
inherently regulated by the speed controller) so I never worry too much
about power supply quality except for the safety aspects (component failure
in the power supply should not cause sparks and flames.)

Phil Weldon

"Dirty Harry" <nothin.DeleteThis@nowhere.com> wrote in message
news:XkMri.18755$_d2.14379@pd7urf3no...
|
| "Phil Weldon" <not.disclosed.DeleteThis@example.com> wrote in message
| news:w3Mri.14336$zA4.11748@newsread3.news.pas.earthlink.net...
| > 'DeanB' wrote:
| > | My problem is that the 12v line is dropping all the way down to 11.5
| > when
| > | the system is under load. I have 2 raid arrays and one usb HD so
there
| > | is a total of 5 drives all together. I think i'm going to do this,
set
| > a
| > power
| > | supply for the hard drives on a switch (green connected to a ground)
and
| > | then fire that up first and then turn on the computer power. The
| > system
| > | is always running 24/7 so it shouldn't be too much of an issue for
| > booting
| > | up. What do ya think?
| > _____
| >
| > The specifications of ATX12V for the 12 volt lines are 12 volts +/- 5%,
or
| > 11.4 to 12.6 volts, so your readings are within specifications ( see
| > <http://www.formfactors.org/developer/specs/ATX12V%20PSDG2.01.pdf>
| > 3.2.1 DC Voltage Regulation
| > page 12)
| >
| > If you are not actually having problems, I wouldn't change things. (The
| > USB
| > hard drive has its own power supply, a wall wart, right?)
| >
| > If you do use the second power supply, I think your method is the way to
| > go.
| >
| > Phil Weldon
| >
|
|
| I'm not having any problems at stock speeds, I can't OC this thing at all
| though lol. Just feel like having some fun squeezing some extra speed out
| of it. Its an amd 3800+ 64 bit....My GF's 3700+ can overclock like crazy
| (230+fsb) I turn this one up to 203 fsb and I'm crashing lol. The
problem
| is I'm only using a generic 400w ps I think...I just wanna see if that's
my
| OC problem or not...I know I know, get a real power supply hehe...I will
| when I have some moola.
| Thanks for the advice!
| Cheers
|
|
 >> Stay informed about: How can I use 2 power supplies at once 

Hey Guy
Not too sure if this helps.
I ran 2 250WATT PSU on my old system if you solder the "startup" and
ground wires in the 24 pin plugs of the two supplies together when you
power up the motherboard both supplies will turn on. i ran this system
for over 2 years but i was running the system off the main supply and
all the fans, lights, water pump off the second one. what you could
probably do is run the system off one PSU and your GPU off the other.
Cheers
 >> Stay informed about: How can I use 2 power supplies at once 

<holmes.mathew.DeleteThis@gmail.com> wrote in message
news:1185953841.963037.110550@r34g2000hsd.googlegroups.com...
> Hey Guy
> Not too sure if this helps.
> I ran 2 250WATT PSU on my old system if you solder the "startup" and
> ground wires in the 24 pin plugs of the two supplies together when you
> power up the motherboard both supplies will turn on. i ran this system
> for over 2 years but i was running the system off the main supply and
> all the fans, lights, water pump off the second one. what you could
> probably do is run the system off one PSU and your GPU off the other.
> Cheers


Hey thats not a bad idea either, the video card is the next biggest power
sucker next to the cpu I'm guessin. Hopefully there wouldn't be any ground
issues with the card getting power from both supplies...guess I could try
and find out, its only a 7600 vid card.
 >> Stay informed about: How can I use 2 power supplies at once